Skip to content
Tape measure laid across a white slatted radiator cover in a bright UK living room

How to Measure for a Radiator Cover (and Do They Really Reduce Heat?)

To measure for a radiator cover, measure the radiator's width valve to valve (not pipe to pipe), then add roughly 5cm. Do the same for height and depth, adding about 5cm of clearance on each so the cover closes properly over the pipework. Opal Retail's own covers run from a compact 78cm model up to an adjustable 139 to 208.5cm design, so once you have your numbers there's usually a ready-made fit. The second question people ask is whether a cover makes the room colder. It can, but how much depends on the design you pick, not on the fact that it's covered at all. Here's how to get both right.

In this article

How Do I Measure My Radiator for a Cover?

You only need a tape measure and somewhere to write down three numbers. Measure the radiator itself, not the wall space around it.

  1. Width, valve to valve. Measure from the outside edge of one valve to the outside edge of the other, including the valve housings, not just the radiator panel. Add about 5cm so the cover clears both valves with room to spare.
  2. Height. Measure from the floor (or from the top of the skirting board if the cover will sit over it) to the top of the radiator. Add 3 to 5cm so the cover isn't resting directly on top of it. If your floor isn't level, measure at both ends and use the taller figure.
  3. Depth. Measure from the wall to the front of the radiator, then check for any pipework or TRV body that sticks out further than the radiator face, and measure to that instead. Add about 5cm of clearance so the front sits clear of the pipework.
  4. Check your thermostatic valve (TRV) height. Note how high the valve head sits. If it's taller than the gap under the cover's base cut-out, it needs to stay outside the cabinet rather than be boxed in (more on why below).

A worked example. Say your radiator measures 62cm valve to valve, 58cm high and 8cm deep to the furthest pipework. Add 5cm to the width (67cm), 4cm to the height (62cm) and 5cm to the depth (13cm). You need a cover with internal clearance of at least 67 x 13 x 62cm (W x D x H). The compact slatted cover below has 72.3 x 17 x 80.3cm inside, so it fits with room to spare.

Check these before you order:

  • Window sill above. The cover's overall height has to sit under the sill. Measure from the floor to the underside of the sill.
  • Skirting board. Decide whether the cover will sit in front of the skirting or over it, and measure your height from that point.
  • Sockets, curtains and bay windows. Check nothing sits in the cover's footprint, and remember a curved bay wall won't suit a straight-backed cabinet.
  • Valve access. You still need to reach the valves to bleed or turn the radiator off.
Tape measure held valve to valve across a radiator to measure width before buying a cover
Measure valve to valve, not radiator panel to panel, then add your clearance.

Radiator Cover Sizes at a Glance

Once you have your three numbers, compare them against the internal clearance of the cover, not just its overall size. These are four of Opal Retail's own covers with their real dimensions, so you can see how the maths works in practice.

Cover Overall size (W x D x H) Internal clearance (W x D x H) Best for
Compact slatted cover 78 x 19 x 81cm 72.3 x 17 x 80.3cm Small single radiators, narrow alcoves
Extendable slatted cover 139 to 208.5 x 20.5 x 82.5cm 131 to 201 x 17 x 81cm Longer radiators, or if you're between sizes
Oak cover with storage drawer 78 x 19 x 95.5cm 73 x 14.5 x 81cm Taller radiators, hallway storage
Long horizontal-slat cover 152 x 19 x 81cm 146.8 x 16.8 x 80.3cm Wide radiators under windows or bay windows

If you're between two sizes, go larger rather than tighter. A roomy cover still works; a tight one will foul the valve or sit flush against the radiator, which is the mistake below.

As a quick guide, add 5cm to your valve-to-valve width and match it to the internal width:

Your radiator, valve to valve Cover that fits
Up to 67cm Compact slatted cover or oak cover with storage drawer
68 to 125cm None of these four. Browse the full radiator cover range for a closer fit
126 to 141cm Long horizontal-slat cover or extendable slatted cover
142 to 196cm Extendable slatted cover
White extendable radiator cover with slatted design and storage shelf
Not sure of your exact size yet?
White Extendable Radiator Cover

Adjusts from 139cm to 208.5cm wide, so it covers a range of radiator lengths without an exact cut.

What's the Most Common Sizing Mistake?

It isn't getting the width wrong. It's the height and depth. Homeowners often measure the radiator panel but forget the valve housing sticking out at the side, or buy a cover that's a touch too short, so the lid ends up resting directly on top of the radiator.

  • Valve clearance missed. Measure outside edge to outside edge of the valves themselves, not just the radiator panel, or the cover will foul the valve on fitting.
  • Cover too short. A lid sitting flush on the radiator blocks the upward airflow it relies on. Leave a genuine air gap above, not just a tight fit.
  • Thermostatic valve boxed in. A TRV sealed inside the cabinet reads the trapped cabinet air, not the room, so it shuts the radiator off early. Keep the valve head outside the cover or use a design with a cut-out.
Slatted radiator cover cabinet with grill, 78 x 19 x 81cm, white
For smaller radiators
Compact Slatted Radiator Cover, 78 x 19 x 81cm

72.3cm of internal clearance, with a slatted grill front that keeps the valve and airflow accessible.

Do Radiator Covers Reduce Heat?

Yes, to some degree, and anyone telling you a cover makes no difference at all isn't being straight with you. Heating engineers have worked from a rule of thumb for years (CIBSE Guide B, the standard UK industry reference) that a fully encased radiator can lose in the region of 20% or more of its output.

An independent study by engineers at Liverpool John Moores University (the paper is on the university's research archive) measured two real products against a bare radiator rather than relying on a rule of thumb. It reported output losses of up to 40% for a traditional timber casing, well above CIBSE's 20% floor, and far less, around 11%, for a thin magnetic radiator wrap, which is a different product to a furniture-style cover. The study didn't test a solid cabinet against a vented one side by side, but the mechanism is well understood: anything that blocks the convection current rising off a radiator reduces its output, so a cover with a genuine air gap and a slatted or lattice front interferes far less than a sealed box. That's why the covers in this guide all use a slatted front rather than a solid panel.

The practical takeaway is to look at how open the front is. Trade guidance quoted in the UK home press suggests aiming for roughly a third or more of the front to be open slats or grille, and the more solid the cover, the more heat you should expect to lose. Treat that as a rule of thumb rather than a measured figure.

Slatted radiator cover with a top shelf and ventilation gaps that let warm air circulate into the room
A slatted front with a genuine air gap top and bottom is what keeps heat moving into the room.

How Do I Stop a Radiator Cover Blocking the Heat?

  • Choose a vented or slatted front, not a solid panel. Slats let warm air flow out continuously instead of pooling inside the cabinet. Aim for roughly a third or more of the front to be open.
  • Leave a real air gap above the radiator. That's what your height measurement (plus 3 to 5cm) is for. Don't trim it tight to save a centimetre, and don't stack things on the shelf that could block the top vent.
  • Keep the thermostatic valve outside the cover, or fully exposed through a cut-out. A valve reading cabinet air will shut the radiator off too early.
  • Don't let the lid rest on the radiator. Even a vented front loses most of its benefit if the top is touching the radiator directly.
Thermostatic radiator valve left outside the cover so it can still read room temperature accurately
Leave the TRV outside the cover so it reads the room, not the cabinet.
Radiator cover cabinet with horizontal slats, 152 x 19 x 81cm, white
For wide or long radiators
Horizontal-Slat Radiator Cover, 152 x 19 x 81cm

146.8cm of internal clearance with a horizontal slatted front, suited to long radiators under a window.

If you want hidden storage alongside the cover, Opal Retail's oak-finish cover adds a top drawer without giving up the slatted front that keeps heat moving.

Radiator cover with storage drawer, slatted heat-safe design, oak
With storage
Oak Radiator Cover with Storage Drawer

95.5cm tall with a slatted front and a 5kg-capacity top drawer for hallway or living room odds and ends.

A cover is only one part of keeping a room comfortable. If your radiator is struggling, our heating and cooling range covers heaters, electric fires and dehumidifiers too.

Related guides: radiator cover buying guide and efficiency and running cost guide. This guide is part of our complete guide to keeping a room warm and dry.

Frequently Asked Questions

What size radiator cover do I need?

Measure your radiator's width valve to valve, its height to the top, and its depth to the furthest pipework, then add roughly 5cm on width and depth and 3 to 5cm on height. Compare those numbers against the internal clearance of the cover, not its overall outside size.

Are radiator covers worth it?

If you want to tidy up an old or mismatched radiator and gain a shelf or drawer, yes, provided you pick a vented or slatted design. If keeping every last bit of output matters more than the look, a repainted or replacement radiator is more efficient.

Is it a fire risk to have a radiator cover close to the radiator?

Radiator covers are made to sit over radiators, and a normal central-heating radiator runs far cooler than the temperature at which wood ignites. Even so, follow the manufacturer's instructions, keep an air gap around the radiator and don't store fabrics or paper on the shelf. A tight fit is mainly a heat-efficiency problem, but leaving room is the safer habit too.

Do I need to remove or move my thermostatic valve (TRV)?

You don't need to remove it, but it does need to stay outside the cover or exposed through a cut-out, or it will read the trapped cabinet air and switch the radiator off before the room has actually warmed up.

Can I build my own radiator cover instead of buying one?

Plenty of people do, usually from MDF with a slatted or grille front, following the same sizing rules above. The trade-off is time and tools against a ready-made cover that arrives pre-cut to size.

Shop Opal Retail's Radiator Covers

Slatted and vented designs from 78cm up to a 208.5cm extendable fit, so most UK radiators are covered.

Shop Radiator Covers →

Free UK delivery on all orders.

Previous article Dehumidifier vs Humidifier: Which One Do You Actually Need?
Next article Wall Mounted vs Inset vs Freestanding Electric Fires: Which Should You Buy? (UK Guide)
Your cart

Your cart is empty

Continue shopping